Guaranteed Analysis: 

Derived from:   

Ammonium Hydroxide, Phosphoric Acid, Acetic Acid,  Plant Growth Regulators, Bio-Lith, Sea Solids, Copper EDTA, Manganese EDTA, Calcium EDTA, Vitamin B-12 and Ascorbic Acid 

CAUTION 

KEEP OUT OF REACH OF CHILDREN 

Harmful if swallowed.  Avoid breathing spray mist.  May cause irritation of eyes, nose, throat or skin.  Avoid contact with eyes, skin, or clothing.  In case of contact with eyes, flush with clean water for at least 15 minutes.  Consult physician if irritation persists. 

CONDITIONS OF SALE 

Seller warrants that the product conforms to its chemical description and is reasonably fit for the purposes stated on the label when used in accordance with directions under normal conditions of use, but neither this warranty nor any other warranty of fitness for a particular purpose, expressed or implied, extends to the use of this product contrary to label instructions or under abnormal conditions, or under conditions not reasonably foreseeable to seller and buyer assumes the risk of any such use.  Seller shall not be responsible for incidental or consequential damages, if any resulting from a breach of warranty. 

MIXING INSTRUCTIONS 

BRT R1 Seed Set mixes completely in water with minimal agitation. 

1. Fill tank roughly ½ full of water and begin agitation. 

1. Add BRT R1 Seed Set to mix tank 

1. Add other nutrients (be sure to check compatibility prior to mixing). 

ATTENTION: Always check compatibility with other products prior to use. 

GENERAL INFORMATION 

BRT R1 Seed Set was designed to exceed typical industry standards for foliars. Generally the industry has used their leftover Starters (9-18-9, 6-26-6) for foliars. Due to their formulations, they don’t work well as foliars, but excel as starters. We designed our foliar with the plant’s physiology in mind and an understanding of the plant’s growth stages. You gain predictable yield with a competitively priced product. 

BRT R1 Seed Set was formulated to be applied at 20 gals/acre water with a minimum of 80 psi.  The written visual would be as follows: on a 40 rod length, 20 rods of fog should be visible, which would be no more than 3 feet above the ground. This type of application will ensure the droplet size is small enough to be absorbed through the stomata. Always use Reverse Osmosis water when possible.  

DIRECTIONS FOR USE 

Corn:  1-2 gals/acre mixed with water for a 20 gals/acre mix. Apply at pre-tassel and early blister stage.  Aerial application rate is 1 gal/acre BRT R1 Seed Set with 2-3 gallons of water. 

Soybeans:  2-3 qts/acre mixed with water for a 20 gals/acre mix. Apply at the first flower set, R1, usually around the equinox (June 21st).  Can be applied thru the R4 stage. 

Small Grains:  1-2 gals/acre mixed with water for a 20 gals/acre mix.  Apply just ahead of boot stage. 

Vegetables and Flowers: 4-5 oz. mixed with water in a per gallon mix. Apply prior to flower bud set. 

All other crops: 1-2 gals/acre mixed with water for a 20 gals/acre mix, prior to seed set or fruit set. 

GUARANTEED ANALYSIS: 

Derived from: 

Humic acid, Aulmic acid, Fulvic acid, Natural Plant Growth Regulators, Seaweed, and Bio-Lith 

KEEP OUT OF REACH OF CHILDREN 

CAUTION 

Harmful if swallowed.  Avoid breathing spray mist. May cause irritation of eyes, nose, throat or skin.  Avoid contact with eyes, skin, or clothing.  In case of contact with eyes, flush with clean water for at least 15 minutes.  Consult physician if irritation persists. 

CONDITIONS OF SALE 

Seller warrants that the product conforms to its chemical description and is reasonably fit for the purposes stated on the label when used in accordance with directions under normal conditions of use, but neither this warranty nor any other warranty of fitness for a particular purpose, expressed or implied, extends to the use of this product contrary to label instructions or under abnormal conditions, or under conditions not reasonably foreseeable to seller and buyer assumes the risk of any such use.  Seller shall not be responsible for incidental or consequential damages, if any resulting from a breach of warranty. 

MIXING INSTRUCTIONS 

Foliar Stimulate mixes completely in water with minimal agitation. 

1. Fill tank roughly ½ full of water and begin agitation. 

1. Add Foliar PGR + to mix tank. 

1. Add other pesticides and/or nutrients (be sure to check compatibility prior to mixing). 

ATTENTION: Always check compatibility with other products prior to use. 

GENERAL INFORMATION 

Foliar PGR + is produced by combining natural Plant Growth Regulators with organic carbons, naturally- occurring carbon Bio-Lith, and Seaweed. Foliar PGR +  has a broad application list including corn, soybeans, vegetables, fruit and nut trees and more. It may be added to early foliar programs or used as a stand-alone product. Foliar PGR + can also be applied through drip irrigation systems. To ensure best performance, only use Foliar PGR + when there is adequate humidity, moderate temperatures and adequate soil moisture.  

Foliar PGR + works well for plant recovery from herbicide, hail, wind, and rain damage.  Each application rate will vary depending on the severity of damage and which growth stage the plant is in. 

DIRECTIONS FOR USE 

FOLIAR APPLICATION RATES: 

Corn, Sweet Corn, Cotton, Small Grains, and Soybeans: Use 24 oz/acre with water for a 15-20 gals/acre mix. When crop is under chemical and environmental stress apply at a 48-96 oz/acre rate.  

Vegetables, Field Crops, Small Fruits, Fruit and Nut Trees:  Apply 24 oz/acre with water for a 15 gals/acre mix.  Multiple applications may be useful.  Using Contact (a non-ionic spreader/sticker) may enhance coverage and increase nutrient uptake.  Do not apply more than 3 times per growing season.  Do not apply when the crop is under severe stress.  For best results, use the lowest possible volume that will ensure complete coverage and small droplet size. 

IRRIGATION RATES: 

Drip Irrigation (All Crops):  Use 48 ounces per acre. Continue irrigation for at least 2 hours to ensure adequate fertilizer coverage. 

Vegetables: Use 48 oz/acre for sprinkler-irrigated fields. Spray or dribble on the seed furrow at planting. For irrigated fields, flood irrigate directly below the seed row 1-2”. 

TECHNICAL DATA INFORMATION 

Ingredients: Borax, Copper sulfate, Cobalt, Iron sulfate, Manganese sulfate, Molybdenum, Zinc sulfate, natural occurring plant growth regulators, organic carbons, tree oils, plant extracts, and Bio-Lith. 

KEEP OUT OF REACH OF CHILDREN CAUTION - MAY CAUSE IRRITATION PRECAUTIONARY STATEMENTS:  Avoid prolonged or repeated contact with eyes, skin and clothing.  Chemical goggles or a full-face shield should be worn.  To protect skin, wear appropriate protective equipment, such as rubber or plastic aprons, rubber gloves and boots.  Avoid breathing mist or vapor.  Keep containers closed.  Wash thoroughly after handling.  May cause gastrointestinal distress, if swallowed. 

HANDLING AND STORAGE:  Minimize skin exposure.  Store mini-bulks and smaller containers out of sun in an area of moderate temperature.  Do not re-use containers.  Avoid containers, piping or fittings made of copper-containing alloys or galvanized metal.  Dispose of containers in accordance with local regulations and requirements. 

FIRST AID:  In case of contact with eyes, immediately flush eyes with water for at least 15 minutes.  Seek immediate medical attention if irritation occurs.  In case of skin contact, flush skin with water.  If irritation occurs, seek immediate medical attention.  Remove and wash contaminated clothing before reuse.  If swallowed, give large amounts of water and induce vomiting by touching the back of the throat with finger unless unconscious.  Seek immediate medical attention. 

IN CASE OF SPILL:  Contain spill and maximize recovery.  Keep spill out of water sources.  Exercise caution in area of spill for slippery conditions.  Dispose of spilled material in accordance with regulatory requirements. 

PHYTOTOXICITY:  Plant and leaf injury may occur on some crops when certain weather and growing conditions are present. Before handling this product, consult the Material Safety Data Sheet for handling, safety and first aid information Follow directions carefully, including precautions for safe handling. 

CONDITIONS OF SALE:  This product conforms to the chemical description on the label thereof and is reasonably fit for the purposes stated on such label only when used in accordance with directions under normal use conditions.  Follow directions carefully.  Timing and method of application, weather and crop conditions, mixture with other chemicals not specifically recommended and other influencing factors in the use of this product are beyond the control of the seller.  Buyer assumes all risks given herewith.  In no case shall the seller be liable for consequential, special or indirect damages such as loss of profits or values resulting from the use or handling of this product 

V3 Foliar Micros + PGR is a complex formula using our original V5 Foliar Micros formula with added plant hormones along with natural plant growth regulators and our latest technology of using a Nano-surfactant.  Quantum mechanical effects are very important at this scale. Glucoheptonate is added as a natural, biodegradable chelating agent to keep boron, copper, cobalt, iron, manganese, molybdenum and zinc available for plant uptake. V3 Foliar Micros + PGR is effective in foliar and soil applications. 

DIRECTIONS FOR USE: 

Attention:  V3 Foliar Micros + PGR contains 0.5% phosphite (a salt of phosphorous) that has been shown to reduce the susceptibility to fungal and bacterial root diseases.  The phosphite component reduces the ability to successful tank mix with some other agricultural products.  V3 Foliar Micros +PGR is NOT compatible with phosphate fertilizers and should be mixed and applied separately.  Contact BRT for advice or perform your own “jar test” for compatibility. 

Corn, sweet corn, sorghum and seed corn: 1 quart per acre sprayed with Pursanova or RO water at 15-20 gallons per acre. 

Soybeans, edible beans, green beans, peanuts and cotton: 1 quart per acre sprayed with Pursanova or RO Water at 15-20 gallons per acre. 

Small grains; 1-2 quarts per acre at tillering, with Pursanova or RO water at 15-20 gallons per acre.                                   Aerial Application:    2-3 Pints/Acre                                          Soil Application: 2-4 Quarts/Acre      

At least one and as many as three applications can be used.  More frequent applications of 1 ½ quarts per acre may be needed to correct deficiencies. Mix with sufficient water for adequate coverage.  V3 Foliar Micros +PGR mix is not compatible with phosphate fertilizers and should be mixed and applied separately. 

A liquid copper solution designed for foliar and soil applications.  Applied to manage plant microbial afflictions and correct copper deficiencies. 

Guaranteed Analysis 

Derived from: Copper Sulfate, Phosphoric Acid, Nicoratic Acid, and naturally occurring carbons 

KEEP OUT OF REACH OF CHILDREN 

CAUTION - MAY CAUSE IRRITATION 

PRECAUTIONARY STATEMENTS:   

Handle with Caution. Foliar Copper has a pH of 1 

Avoid prolonged or repeated contact with eyes, skin and clothing. Observe all safe handling procedures in the Private Applicator Manual for low pH liquid materials. Chemical goggles or a full-face shield should be worn.  To protect skin, wear appropriate protective equipment, such as rubber or plastic aprons, rubber gloves and boots.  Avoid breathing mist or vapor.  Keep containers closed.  Wash thoroughly after handling.  May cause gastrointestinal distress, if swallowed. 

HANDLING AND STORAGE:  Minimize skin exposure.  Store mini-bulks and smaller containers avoiding prolonged exposure to direct sunrays in a cool dry environment.  Do not re-use containers.  Avoid containers, piping or fittings made of copper-containing alloys or galvanized metal.  Dispose of containers in accordance with local regulations and requirements. 

FIRST AID:  In case of contact with eyes, immediately flush eyes with water for at least 15 minutes.  Seek immediate medical attention if irritation occurs.  In case of skin contact, flush skin with water.  If irritation occurs, seek immediate medical attention.  Remove and wash contaminated clothing before reuse.  If swallowed, give large amounts of water and induce vomiting by touching the back of the throat with finger unless unconscious.  Seek immediate medical attention. 

IN CASE OF SPILL:  Contain spill and maximize recovery.  Keep spill out of water sources.  Exercise caution in area of spill for slippery conditions.  Dispose of spilled material in accordance with regulatory requirements. 

CONDITIONS OF SALE:  This product conforms to the chemical description on the label thereof and is reasonably fit for the purposes stated on such label only when used in accordance with directions under normal use conditions.  Follow directions carefully.  Timing and method of application, weather and crop conditions, mixture with other chemicals not specifically recommended and other influencing factors in the use of this product are beyond the control of the seller.  Buyer assumes all risks given herewith.  In no case shall the seller be liable for consequential, special or indirect damages such as loss of profits or values resulting from the use or handling of this product 

Foliar Copper 5% Phosphite 

Foliar Copper was formulated to provide the grower with a nutritional aid. Copper is a regulator of or an essential cofactor in various enzyme systems involved in plant defense against infection.  Copper is also an essential micro-nutrient element for plant growth and disease resistance.  Phosphite promotes a plant’s natural defense system and induces the synthesis of phytoalexins, which strengthens resistance to invasions of bacteria and fungus.  Phosphite is also known to enhance the translocation of minerals within the plant. This product is most effective when tank-mixed with BRT Bulker, which provides a late season burst of nutrients (bulks up the grain or seed), stimulates the defensive biochemistry, and minimizes the risk of yield loss, due to environmental stresses. 

DIRECTIONS FOR USE 

Corn: Apply 1 pint/acre Foliar Copper with 2 quarts/acre BRT Bulker, mixed with 15-20 gal. reverse osmosis (RO) water. Apply at post tassel, R-3 to R-5 stage of growth. 0.5 to 1 pt. may be used at the V-3 stage to help deter Goss’s Wilt. 

Soybeans: Apply 1 pint/acre Foliar Copper with 2 quarts/acre BRT Bulker, mixed with 15-20 gal. reverse osmosis (RO) water. Apply at R-6 to R-8 stage of growth (late season). 

Vegetables: Apply 1 pint/acre Foliar Copper with 2 quarts/acre BRT Bulker, mixed with 15-20 gal. reverse osmosis (RO) water. Apply at early fruit formation.

Guaranteed Analysis: 

Derived from:   

Ammonium Hydroxide, Phosphoric Acid, Potassium hydroxide. 

KEEP OUT OF REACH OF CHILDREN 

CAUTION 

Harmful if swallowed.  Avoid breathing spray mist.  May cause irritation of eyes, nose, throat or skin.  Avoid contact with eyes, skin, or clothing.  In case of contact with eyes, flush with clean water for at least 15 minutes.  Consult physician if irritation persists. 

CONDITIONS OF SALE 

Seller warrants that the product conforms to its chemical description and is reasonably fit for the purposes stated on the label when used in accordance with directions under normal conditions of use, but neither this warranty nor any other warranty of fitness for a particular purpose, expressed or implied, extends to the use of this product contrary to label instructions or under abnormal conditions, or under conditions not reasonably foreseeable to seller and buyer assumes the risk of any such use.  Seller shall not be responsible for incidental or consequential damages, if any resulting from a breach of warranty. 

MIXING INSTRUCTIONS 

8-19-3 mixes completely in water with minimal agitation. 

1. Fill tank roughly ¼ full of water and begin agitation. 

1. Add 8-19-3 100% Ortho Starter to mixing tank. 

1. Add other nutrients (be sure to check compatibility prior to mixing). 

ATTENTION: Always check compatibility with other products prior to use. 

GENERAL INFORMATION 

8-19-3 100% Ortho Starter was designed to exceed the industry standards for starters. We formulated ours with 100% Orthophosphate whereas most companies build theirs with 80% Ortho and 20% Polyphosphate. Since you only have one chance to affect your crop at planting time, we decided to only formulate the highest quality starters while keeping the plant physiology in mind and a strong understanding of the growth stages of the crop. You gain predictable yield with a quality and price competitive product. 

DIRECTIONS FOR USE 

Corn:  3-5 gals/acre in furrow 

Soybeans:  1-3 gals/acre in furrow 

Small Grains:  1-2 gals/acre in furrow  

All other crops: 1-2 gals/acre 

Derived From:                                                                

Humic acid, Fulvic acid, carbohydrates, and natural fractured polyhydroxy acids, Trichoderma, Azotobacter, and Mycorrhizae. 

General Information:                                                       

BRT Hume is a soil biology activator, meaning it is made up of soil micro-organisms. BRT Hume establishes a growth medium for beneficial soil microbiology. This allows the microbes to explosively repopulate in their soil environment. Their rate of growth and metabolism increases. This will aid the crop in resisting soil pathogens and also reduces crop stress due to environmental changes.  As the microbial population increases, fertilizer and nutrients are more readily available to the roots in a plant usable form. BRT Hume can be mixed with most fertilizers and soil amendments. BRT Hume is a dark brown liquid. 

PRECAUTIONARY STATEMENTS: KEEP OUT OF REACH OF CHILDREN. CAUTION – MAY CAUSE IRRITATION. Harmful if swallowed. Avoid breathing spray mist. May cause irritation of eyes, nose, throat or skin. Avoid contact with eyes, skin or clothing. In case of contact with eyes, flush with clean water for at least 15 minutes. Consult a physician if irritation persists. 

CONDITIONS OF SALE: Seller warrants that the product conforms to its chemical description and is reasonably fit for the purposes stated on the label when used in accordance with directions under normal conditions of use, but neither this warranty no any other warranty of fitness for a particular purpose, expressed or implied, extends to the use of this product contrary to label instructions or under abnormal conditions, or under conditions not reasonably foreseeable to seller and buyer assumes the risk of any such use. Seller shall not be responsible for incidental or consequential damages, if any resulting from a breach of warranty.

DIRECTIONS FOR SOIL APPLICATION RATES: 

Corn, Cotton, Soybeans, and most Field Crops:                Apply 2-4 qts/acre BRT Hume in 20 gallons of water. BRT Hume can be mixed with most fertilizers.  It works well with sidedress liquid nitrogen since it has shown to help stabilize nitrogen. Do not apply more than twice per growing season.  

HUMIC ACID MODEL 

General Information 

Derived From:                                                                

Humic acid, Fulvic acid, carbohydrates, and natural fractured polyhydroxy acids, and Ascolphyllum nodosum Seaweed. 

BRT SW37 is a premium biologically-based fertilizer additive. It is most effective when soil- applied, but can be applied as a foliar. BRT SW37 contains Ascophyllum nodosum seaweed which stimulates the soil microbes by acting as a food source. It also is effective as a foliar, providing natural plant growth hormones and essential enzymes derived from the seaweed. 

DIR 

PRECAUTIONARY STATEMENTS: 

KEEP OUT OF REACH OF CHILDREN.  

CAUTION – MAY CAUSE IRRITATION.  

Harmful if swallowed. Avoid breathing spray mist. May cause irritation of eyes, nose, throat or skin. Avoid contact with eyes, skin or clothing. In case of contact with eyes, flush with clean water for at least 15 minutes. Consult a physician if irritation persists. 

CONDITIONS OF SALE: Seller warrants that the product conforms to its chemical description and is reasonably fit for the purposes stated on the label when used in accordance with directions under normal conditions of use, but neither this warranty nor any other warranty of fitness for a particular purpose, expressed or implied, extends to the use of this product contrary to label instructions or under abnormal conditions, or under conditions not reasonably 

foreseeable to seller and buyer assumes the risk of any such use. Seller shall not be responsible for incidental or consequential damages, if any resulting from a breach of warranty. 

DIRECTIONS FOR USE:

BRT SW37 can be used on both corn and soybeans at the same rate. 

Soil – Use 1-2 quarts/acre in 15-20 gallons of water. Can be mixed with most fertilizers. 

Foliar -Use 1-2 pints/acre in 15 gallons of water. Apply before flowering and again at fruit set. 

Guaranteed Analysis 

Derived From: 

Calcium Nitrate, Phosphoric Acid, Mono-potassium Phosphate, Bio-Lith, Humic Acid, Fulvic Acid and Natural Plant Hormones. 

General Information 

The development of Legume Booster is very unique to our industry. The combination of calcium and phosphorus has increased hay crop yields with increases up to 1,150 lbs. per acre per cutting. Legume Booster also has increased quality, aiding in tighter ADF and NDF, while directly increasing Calcium. The final response is a healthier, more nutrient-dense crop, with a higher Brix reading, and a quicker recovery after each cutting. 

Mixing Instructions 

Legume Booster mixes completely in water with 

minimal agitation. 

1. Fill tank ½ full of water and begin agitation.

2. Add Legume Booster to mix tank.

3. Add other pesticides/nutrients (be sure to check compatibility prior to mixing).

Attention: Always check compatibility with other 

products prior to use. 

DIRECTIONS FOR US 

Foliar application rates: 

Vegetable, Field Crops, Small Fruits, Fruit and Nut Trees: 

Apply 1-3 quarts of Legume Booster in at least 5 

gals of water/acre. Multiple applications may be useful.  

On individual trees use 4-6oz/gallon and wet down completely. Start at pre-bloom - follow up every 10-14 days; applying up to 3 times per growing season. 

Do not apply when the crop is under severe stress. For best results, use Contact (non-ionic spreader/sticker) to enhance coverage, and increase nutrient-uptake. Ensure complete coverage with smallest droplet size.  

Alfalfa, clover and grass hay: Use 2.5 quarts of Legume Booster per acre in a 15-20 gal/acre mix with water per acre. Apply after each cutting. 

Soil Application Rates:  

Corn, Cotton, Melons: Inject ½” - 2” directly below and/or to the side of the seed furrow. Use 3-10 gal. /acre. Dilute Legume Booster with water for better coverage. 

Vegetables: For sprinkler-irrigated fields, spray or dribble 2 x 2 from the seed at planting. For furrow-irrigated fields, inject directly below the seed row 1-2”. Use 2-5 gals/acre. Dilute Legume Booster with water for better coverage. 

Drip Irrigation (All Crops):  

Use 3-10 gallons of Legume Booster mixed with water before injecting into irrigation lines. Continue irrigation for at least 2 hours to ensure adequate fertilizer coverage.